Features & Options
* Scope of supply
* Options
Features of the Uniparker 5003
*
Control element incl. emergency stop in automatic-control
with brief operating instructions and wiring to switch
cabinet.
* Installation with
sliding platforms and one empty space on the entrance
level and with movable platforms on the level above
and below.
* Width of lot 230cm
and depth of pit 175 cm and inside height 345cm as standard
* Width of lot modified 240cm and wider or version
depth of pit 200 recommended for higher conveniences
* Mono-hub cylinder
to drive the horizontal movable platforms with looped-around
suspension elements, sliding platforms with electrical
drive
* entering wedge
for car positioning.
* Safety device to
prevent kneeling by leakage, pipe burst, fracture of
suspension elements.
*
Mounting of installation and aggregate with HD-anchors,
electrical wiring with impact dowels
* Bounded anchors for increased foundation requirements
*
Drive unit "Silencio" with tubing and wiring
to the installation
* Structure-borne noise package to comply with
DIN 4109 and adherence to sound insulation measure Rw
Ô55
* Sound insulation hood to minimize airborne
sound
* HVLP-oil for excessive fluctuations in temperature
*
Drive plates in trapezoid style sheeting
* Rubber profiles in the pedestrian area, width
40cm or 60cm, in pedestrian and drive area 60cm and
40cm
* Luxury sheet metal
*
Corrosion prevention "Classic" of drive plates
by continuous line-galvanizing to DIN EN 10142/10143
* Corrosion prevention "Premium" of
drive plates by individual piece-galvanizing to DIN
ISO 1461
** Corrosion
prevention "Classic Plus" of drive plates
by line-galvanizing to DIN EN 10142/10143 and coating
of the top surfaces (dependent on the market needs the
scope of supply contains zinc and powder coated sheet
metal)
* Corrosion prevention "Premium Plus"
of drive plates by individual piece-galvanizing to DIN
ISO 1461 and coating of the top surfaces
*
Sliding doors for fall-danger prevention into the pit
and railings from the platform (Notice: safe guarding
against shearing and squeezing have priority and must
provided by the proprietor sideways and behind the installation)
* Remote control and/or automatic-drive for sliding
doors
* Modem for teleservice for online-analysis and
help
* Assembly of the ramp behind the columns, length
of pit must have at least 560cm
* Vehicle load 2,0
to 5m length according to vehicle data
* Extra capacity of sliding platforms to 2,5
to, vehicle length to 5,10m, pit length plus 10 cm
A maintenance contract is recommended
Intersections/ Customer's duties
• Aggregate power: 400V, 50Hz, three-phase motor
3,0Kw, assembly in pit range or in direct near of the
system, LBH ca 60 x 22 x 40 cm
• Supply line to switch cabinet 5x 1,5mm2, or to
local regulations, fuse protection 3 x 16amp, slow fuse
• Electrical potential equalisation (foundation
ground steel-construction to VDE 0100 T410)
• Telephone line dto by option modem and teleservice,
after consolations
• Free space for switch cabinet LBH ca 60 x 22
x 80cm, with swing door in immediate near to installation
(max 6m) with access to the parking system
• Level surface HxB 50cm x 20cm to attach the control
unit in direct near of the installation
• Safeguarding to DIN EN 294
• Lighting to DIN 67528, illumination of parking
lots and buildings for parking
• Foundation exactly to size, clean and dry Compliance
with installation requirements as per quotation
• The measurements are minimum finished dimensions.
Tolerances to VOB part C (DIN 18330, 18331) should be
considered supplementary. Measurements in cm.
Technical alterations reserved, alterations in the scope
of supply reserved. Version 15/2004 |
